asphalt standard according to astm

asphalt standard according to astm

MATERIAL SPECIFICATION FOR AGGREGATES - HOT MIX ASPHALT

This specification covers material requirements for aggregates for use in hot mix asphalt (HMA). 1003.02 REFERENCES . This specification refers to the following standards, specifications, or publications: Ontario Provincial Standard Specifications, Constr

Learn More

Codes and Standards - NRCA

ASTM D36, "Standard Test Method for Softening Point of Bitumen (Ring-and-Ball Apparatus)," provides a laboratory procedure for testing bitumens with softening points in the range from 86 to 315 F. Bitumens (asphalt, coal-tar pitch) are not characterized b

Learn More

ASTM D3381/D3381M - Standard Specification for Viscosity

For asphalt binders graded by penetration at 25 °C [77 °F], see Specification D946/D946M. If needed, volume corrections for asphalt binders should be made according to Practice D4311/ D4311M. The values stated in either SI units or inch-pound units are to

Learn More

Measuring the density of bitumen/asphalt :: Anton Paar Wiki

The standard test methods (ASTM D70 and EN 15326) ... Measurement with a pycnometer takes around 2 hours according to ASTM D70, ... requires a pycnometer to measure the density of bitumen/asphalt. There is a new ASTM standard for using a digital density m

Learn More

STANDARD CONSTRUCTION SPECIFICATIONS FOR ASPHALT

ASTM D-4125 Standard Test Method for Asphalt Content of Bituminous Mixtures by . Page 2 Standard Construction Specifications Division 40 – Asphalt Surfacing Revised 11/08 Nuclear Method ASTM D-4791 Flat and Elongated Particles ... Standard Construction Sp

Learn More

Accurate Density Determination of Asphalt

The quality and uniformity of the asphalt mixture determines whether a road will be paved evenly to achieve the highest quality, most resilient surface. The standard test method (ASTM D70-09) for measuring and comparing the density of semi-solid bituminou

Learn More

702 ASPHALT MATERIAL

702.13 Rubberized Asphalt Emulsion. Provide material consisting of asphalt emulsion SS-1 or SS-1h, according to 702.04, blended with rubber compound, according to 702.14, to produce a residual mixture of asphalt and rubber solids having a composition of 9

Learn More

ASPHALT PAVEMENT TEXTURING SPECIFICATION PART 1 –

ASPHALT PAVEMENT TEXTURING SPECIFICATION 1 March 2009 March 2009 PART 1 – GENERAL 1.1 ... A. ASTM D-4541 Standard Test Method for Pull-Off Strength of Coatings Using ... A durable and stable asphalt pavement mix design installed according to best

Learn More

ASTM D7173-14 - Standard Practice for Determining the

The results of testing on material prepared according to this practice may be used as a guideline when formulating products or to establish field handling procedures. Large differences in test results between top and bottom specimens indicate that there i

Learn More

ASPHALT PAVEMENT TEXTURING SPECIFICATION PART 1 – GENERAL

ASPHALT PAVEMENT TEXTURING SPECIFICATION 1 March 2009 March 2009 PART 1 – GENERAL 1.1 DESCRIPTION A. Asphalt pavement texturing is a highly suitable solution for a wide variety of decorative pavement applications. Paved entranceways, parking lots, residen

Learn More

MATERIAL SPECIFICATION FOR EMULSIFIED ASPHALT

LS-226 Test for High Float Emulsified Asphalt . ASTM International . D 140/D 140M -09 Standard Practice for Sampling Bituminous Materials . D 1310-01 (2007) Standard Test Method for Flash Point and Fire Point of Liquids by Tag Open-Cup Apparatus . D 2939-

Learn More

ASPHALT CONCRETE PAVEMENT PART 1 GENERAL

ASPHALT CONCRETE PAVEMENT PART 2 PRODUCTS 2.01 ASPHALT CEMENT 2.02 PRIME COAT 2.03 TACK COAT 2.04 AGGREGATES Asphalt cement used in the manufacture of each class of Asphalt Concrete Pavement shall be 150 - 200 (A) Grade conforming to the requirements of A

Learn More

"Standard 30# asphalt " felt vs "ASTM 30# asphalt felt" (ASTM

Sep 11, 2009 · "ASTM has established two standards for asphalt felt. The less stringent standard is ASTM D 4869, which requires Type 1 (#15) felt to weigh at least 8 pounds per 100 square feet. The more rigorous standard, ASTM D 226, requires a minimum w

Learn More

Standard Specification for Viscosity-Graded Asphalt Cement

The purchaser shall specify the applicable table of limits. In the event the purchaser does not specify limits, Table 1 shall apply. For asphalt cements graded by penetration at 77°F (25°C) (see Specification D 946). If needed, volume corrections for asph

Learn More

List of ASTM International standards

This is a list of ASTM International standards. Standard designations usually consist of a letter prefix and a sequentially assigned number. This may optionally be followed by a dash and the last two digits of the year in which the standard was adopted.

Learn More

Leave a comment